U-Line Marine Collection MCR014 Crescent Ice Maker
14" crescent ice maker, marine / 230V from the Marine Collection line — model notes, common issues and related U-Line ice maker service.
Model overview
Before a technician arrives for a crescent ice maker built for marine use, have the model MCR014 and the Marine Collection name ready. The U-Line MCR014 is 14 inches wide, and the questions usually start with ice output: whether production has slowed, whether the cubes look small or cloudy, and whether the bin is melting or refreezing into a single block. Water pooling at the base is another detail to report. Tell the crew when each change started and whether it happens during heat or only at certain hours. Across the metro areas we cover, these notes are the first thing a crew asks for. In the booking form, enter MCR014, describe the output problem, and include any code you saw on the display.
At a glance
| Model | MCR014 |
|---|---|
| Appliance | 14-inch marine crescent ice maker |
| Common symptoms | slowed ice production, small or cloudy cubes, bin melting or refreezing into a block, water pooling at the base |
| What you can check | Have the model number and collection name ready. Note when each change started, whether it happens during heat or at certain hours, and any code on the display. |
| When to call a technician | Ask for a service visit if ice output stays slow, the bin melts into one block or water pools at the base. Describe the output problem and its timing. |
MCR014 is a U-Line 14″ crescent ice maker, marine / 230V from the Marine Collection line. The model number is printed on the rating label, usually on a side wall or the ceiling inside the fresh-food section, or behind the base grille; match it letter for letter before booking, because a single letter can change parts.
Specifications
| Capacity | Ice storage capacity is 12 lb (5.4 kg). |
|---|---|
| Power | Listed 02A variants use 230 V, 50 Hz power. |
| Installation | Supports built-in or freestanding installation. Installation does not require a drain. |
| Features | Maximum daily ice production is 23 lb (10.4 kg). |
| Controls | Uses an on/off switch. |
| Care | Manual specifies condenser cleaning every six months. |
| Finish | Interior finish is white. |
What sets the MCR014 apart
Stainless versions of the MCR014 offer flush-to-cabinet, flush-to-door or no-flange trim, so the face can line up with the cabinetry it sits in. The white interior and an on/off switch keep the controls simple. Installation does not need a drain, and the 12 lb of ice storage sits in a bin the owner can check at a glance.
Service notes for the MCR014
Low ice output on the MCR014 starts with the condenser, which the manual asks the owner to clean every six months, so a technician will ask when it was last cleaned before looking inside. A bin that melts or refreezes into a block points to ambient heat, the on/off switch being left off, or a bin lid left open. Cloudy or hollow crescents are checked against the water supply, and water at the base is noted early because the design needs no drain. Pooled water can come from a loose supply connection or a bin overflow, so the owner can note whether it appears during production or after shutdown.
Questions about the MCR014
Where do I find the MCR014 model number?
Check the rating label on a side wall or the ceiling inside the fresh-food section, or behind the base grille. Use the full number, including any letters at the end.
Do you repair the U-Line MCR014 on site?
Yes. We book in-home visits for this model in the Miami, New York, Houston, Los Angeles and San Diego metro areas. Add the model number and the symptom to the booking form.
What should I note before the visit?
Note whether the water supply was recently changed and how long production has been slow.
Common issues for this model
- No ice or very slow production
- Bin melting or refreezing into a block
- Small, hollow or cloudy cubes
- Water leaking at the base
Related error codes
U-Line Ice Maker Er25 Code: Evaporator Freezing
Er25 on the RNP115 / URNP115 nugget ice machine is an evaporator freezing code tied to ambient temperature.
U-Line Ice Maker Code: 2 Flashes, Thermistor or Too Warm
On the CLR2060 the diagnostic LED flashes two times for an open thermistor or an out-of-range, too warm, condition.
U-Line Ice Machine Code: Condenser T Short Circuit
The U-3018CLRS-40B logs Condenser T Short when the condenser thermistor circuit is shorted.
U-Line Ice Maker No Comm Code: Lost Display Link
No Comm on the U-3018CLRS-40B clear ice machine, with the power-cycle step and the technician checks.
Recommended repair service
U-Line Ice Maker Repair
Ice maker not producing ice, making too little, or leaking? We diagnose U-Line ice makers thoroughly.
Troubleshooting resources
Note whether the water supply was recently changed and how long production has been slow.
Model-information disclaimer. Confirm your exact model number and specifications with your appliance documentation before booking a repair. Model pages are for identification and compatibility reference.
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Request your repair
Fill in the form below and we’ll confirm an appointment.